04 FXSTI Brake still seems to have plenty of stopping power, but doesn't start to apply any braking until lever is about 1 1/2 inches from the handle grip. I've run half a bottle of fluid through it trying to bleed out any air. I've never done anything to the brakes except change out the stock lever for a chrome one. Have about 5000 miles on it. Purchased the bike about 2000 miles ago. My old sporty had almost immediate braking. Is this normal or is there another way to bleed the air out. I have no leaks at all. Thanks for any help.
you can back bleed them by using a screwdriver or scraper to push the pucks in, usually works good just loosen the cap a little bit, try that if you have no luck with that make sure you still have plenty of pad left...
My RK does the same thing and I had only done the same thing (replaced the levers with aftermarkets) The dealer (whom I do trust btw) told me it was because of the new levers. I still trust them but I gotta raise the BS flag on that one. The pads are good so??????
I hear ya RKJ. I have plenty of pad left also. Only thing I can think of is the lever is cast a little different. They are Harley levers though. Dr. Deuce, if you had this problem, how much fluid did you have to run through it before you got all the air out? I can't even really get a good pump up with it. Lever gets hard but doesn't gain any depth. I suppose I could put the original lever back on and see if it makes a difference. Just a pain though. Thanks for the info.
just replaced the stock levers for a pair of chrome Paul Yaffe levers, and experienced the same. The levers appear to be different, in the way that the lever is much closer to the grip when fully breaking.
the lever isnt going to make any difference in braking. if you have braided lines, it takes longer to bleed fully. must be due to the inner material of these lines. uou can also tap on the caliper and tap on the lines to bring the air to the top. just continue to bleed the system, do it each nite for 3 nites. hold hard on the lever, then slowly open the bleeder and see if you get any air out. DO NOT let the lever come back while the bleeder is open. when you get all the air out, the lever will feel very solid when it is applied tight. you want to eliminate the spongy feel, which is the air in the line being compressed...... you cannot compress brake fluid. thats why it'll feel solid when the air is purged. and don't let the fliud in the master cylinder get too low during this porcedure.
The guys in the Indy shop noticed spongy and extended lever travel several times after replacing the pads and fluids in particular in dual disk set ups. Complete disassembly of calipers, master cylinders, all new rubber and overnight bleeding etc. etc. did not solve the problem. The master had no visible issues, the bottom valve appeared to work. Replacing the master cylinder solved the problem every time however. This happened at least 10 times over the last 2 years and only on bike that were 3-5 years old.
Don't know what it is, but they know now what to do..........
Here is a trick I learned over 30 years ago...Take some electrical tape and pull the brake lever in and release it several times (basically flicking it)...then pull the lever all the way in and run 4 or 5 layer of tape around the lever and the throttle grip together. Make sure the lever is all the way in as far as it will pull in...tape tightly.
Let it set over night. Release the tape the next day and see how much more lever you've gained...you'll be suprised. Repeat if neccesary.
Just my 2 cents...from No Cents.:clap:
This is an older thread, you may not receive a response, and could be reviving an old thread. Please consider creating a new thread.
Related Threads
?
?
?
?
?
V-Twin Forum
2.7M posts
145.8K members
Since 2001
V-Twin Harley Davidson forum. Discussion on V-Twin Harley Davidson motorcycles including Dyna, Electra Glide, Softail, Sportster, and more.